Order online or over the phone

call us at 1-888-520-6689 weekdays

8:30am - 5:00pm central time zone

TOLL FREE1-888-520-6689

Wahl MAGIC CLIP Precision Fade Clipper - Model 8451

$ 45.95

Wahl MAGIC CLIP Precision Fade Clipper - Model 8451

$ 45.95


Wahl MAGIC CLIP Precision Fade Clipper - Model 8451
50% More Power

Poweful, Yet cool-running cariable taper and texture baldes adjust to "Zero-Overlap".
MODEL 8451 INCLUDES: Professional Clipper with Adjustable Taper Lever; 8 Cutting Guides (1/16"-1"); Styling Comb; Oil; Cleaning brush and Operating Insturctions; Red Blade Guard (Guarantees Professional Quality).

DIRECTION FOR OPERATION:
1. Put a small drop of Wahl Clipper Oil between the blades after each use. Oil should be applied while the clipper is rtunning. After cutting wet hair,clean the blades and apply a small drop of Wahl Clipper Oil. use Wahl Clipper Oil ONLY> Apply the oil after each use.
2. Blades must be realigned if they have been removed for cleaning or replacement.
3. Streaks and missing hair are caused by a gummy sticky surface on the blades, so keep your clipper clean and the blades well oiled.
4. Clattering when turning the clipper on or off may occur on some clippers. It is of no consequence. The smae is true if your clipper heats up after 20-25 minutes of use.
5. Make sure cord is not twisted or kinked while unit is charging or being stored.
6. To clean the unit, use either a clean, dry or dampeded bloth. Do NOT USE benzene or thinner to clean the unit.

ON THE WAHL CLIPPER: Sketch shows how the bottom blade holes are larger than the shanks of the blade screws. When the blade scerws are loosened the bottom blade can be aligned with the to blade. Keep the screws tight after the blade is aligned.
1. End of top blade teeth should be 1/32" to 1/16", .79mm to 1.59mm back from bottom blade. This is important so that the clipper doesnt cut too close or allow the moving cutter to touch the skin.
2. Extreme left hand tooth of top blade must be covering or be to the left of the first small tooth of bottom balde.
3. Extremeright hand tooth of top balde must be touching the big tooth on the bottom blade.

ON CLIPPERS USING "ADJUSTO-LOC" BLADES: To remove the blades loosen only center screw. Leave the two outside screws tight as they hold bushings in place to keep alignment of blades. Keep screws tight when in oepration.

CORD: If your clipper has a polarized Plug: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug fits in a polarized outlet only one way. In he event the plug does not fit fully in the outlet, reverse the plug.

TAPER LEVER: Some clippers are equipped with an adjustable taper lever that changes the closemess of your cut. When the lever is in the uppermost postion, the claes will give the closes cut. Pushing the lever downward gradually increases the cutting length.

POWER SCREW: (Not found on all clipper models). To adjust power, turn power screw in clockwise direction until clipper makes a noise caused by the armature hitting the coil. Then, slowly turn power screw out (counter-clock-wise) just until noise stops. This is maximum power.

YOUR WAHL ELECTRIC CLIPPER WILL GIVE YOU YEARS OF SATISFACTORY SERVICE IF YOU WILL PUT A FEW DROPS OF OIL ON THE BALDES BEFORE AND AFTER EACH HAIRCUT.

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. This appliance is not suitable for use by people (including children) with physical, sensory or mental disabilities or who do not have the relevant experience or knowledge of using such appliance unless under